• • Four dual-band Nf connectors for external antenna operation
  • One 2.4Ghz IoT Nf connector for the Bluetooth/Zigbee radio
    • 5dBi omni-directional antenna included

AP-585

• • Built in omni-directional antennas (H and V polarized)
  • 5Ghz Antennas 4.5dBi uncorrelated avg (5.8dBi peak)
  • 2.4GHz Antennas 3.0dBi uncorrelated avg (4.4dBi peak)
  • Bluetooth Antenna 4.8dBi peak

AP-587

• • Built in 90°H x 90°V directional antennas (H and V polarized)
  • 5Ghz Antennas 5.2dBi uncorrelated avg (6.6dBi peak)
  • 2.4Ghz Antennas 5.7dBi uncorrelated avg (5.8dBi peak)
  • Bluetooth Antenna 6.3dBi peak

5GHz radio: Four spatial stream Single User (SU) MIMO for up to 2.4Gbps wireless data rate with individual 4SS HE80 (or 2SS HE160) 802.11ax client devices, or with four 1SS or two 2SS HE80 802.11ax MU-MIMO capable client devices simultaneously

2.4GHz radio: Four spatial stream Single User (SU) MIMO for up to 1,150Mbps wireless data rate with individual 4SS HE40 802.11ax client devices or with two 2SS HE40 802.11ax MU-MIMO capable client devices simultaneously

Support for up to 1,024 associated client devices per radio (typical recommended limit for active outdoor clients is 100-200 depending on distance), and up to 16 BSSIDs per radio

Supported frequency bands (country-specific restrictions apply):

• • 2.400 to 2.4835 GHz (ISM)
  • 5.150 to 5.250 GHz (U-NII-1)
  • 5.250 to 5.350 GHz (U-NII-2A)
  • 5.470 to 5.725 GHz (U-NII-2C)
  • 5.725 to 5.850 GHz (U-NII-3/ISM)

Available channels: Dependent on configured regulatory domain

Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

Supported radio technologies:

• • 802.11b: Direct-sequence spread-spectrum (DSSS)
  • 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
  • 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 37 resource units (for an 80MHz channel)

Supported modulation types:

• • 802.11b: BPSK, QPSK, CCK
  • 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension)
  • 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM (proprietary extension)
  • 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM

802.11n high-throughput (HT) support: HT20/40

802.11ac very high throughput (VHT) support: VHT20/40/80/160

802.11ax high efficiency (HE) support: HE20/40/80/160

Supported data rates (Mbps):

• • 802.11b: 1, 2, 5.5, 11
  • 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
  • 802.11n: 6.5 to 600 (MCS0 to MCS31, HT20 to HT40), 800 with 256-QAM
  • 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160), 2,166 with 1024-QAM
  • 802.11ax (2.4GHz): 3.6 to 1,147 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE40)
  • 802.11ax (5GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160)

802.11n/ac packet aggregation: A-MPDU, A-MSDU

Transmit power: Configurable in increments of 0.5 dBm

Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):

• • 2.4 GHz band: +29 dBm (23dBm per chain)
  • 5 GHz band: +28 dBm (22 dBm per chain)
  • Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.

Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks

Maximum ratio combining (MRC) for improved receiver performance

Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance

Space-time block coding (STBC) for increased range and improved reception

Low-density parity check (LDPC) for high-efficiency error correction and increased throughput

Transmit beam-forming (TxBF) for increased signal reliability and range

802.11ax Target Wait Time (TWT) to support low-power client devices

Advanced IoT Existence (AIC) allows for concurrent operation of the IoT and 2.4Ghz radios without issue

802.11mc Fine Timing Measurement (FTM):

• • for precision distance ranging

When both AC and POE power sources are available, AC power takes priority over POE

Power sources are sold separately; see the ordering Information section below for details

See below conditions for each power configuration:

• • When powered by AC, the AP will operate without restrictions, including 802.3af/at support (with upper thermal limitations).* With IPM enabled, the AP will adjust power requirements to meet requirements, and will reduce according to established IPM policy
  • When powered by 802.3bt Class 6, the AP will operate without restriction, limited to 802.3af PSE support.* With IPM enabled, the AP will adjust power requirements to meet requirements, and will reduce according to established IPM policy
  • When powered by 802.3bt Class 5 with LLDP, full function but no PSE support*
  • When powered by 802.3at, AP will reduce both radios to 2 chains only, and will disable PSE out*
  • When powered by 802.3af, the AP will boot up, but not enable any radios, regardless of IPM settings.
    • With IPM enabled, the AP will adjust power requirements to meet requirements, and will reduce power as necessary according to the established IPM policy

Maximum (worst-case) power consumption

• • AC powered: 71W (802.3af/at*)
  • POE powered (802.3bt Class 6): 49.5W (802.3af PSE only)
  • POE powered (802.3bt Class 5 with LLDP): 35.5W (no PSE)
  • POE powered (802.3at, IPM disabled): 25.5W (2 chain @ 2.4Ghz, 2 chains @ 5Ghz, no PSE)

Maximum (worst-case) power consumption in idle mode: 9.2W (POE) or 10.8W (AC)

Maximum (worst-case) power consumption in deep-sleep mode: 3.0W (POE) or 4.4W (AC)

* In some power configurations and conditions, 802.3at may not support the full 30W

AP-270-MNT-H1 – Single-tilt mounting bracket for wall or ceiling

AP-270-MNT-H2 – Flush ceiling or wall mounting bracket

AP-270-MNT-H3 – Dual-tilt mounting bracket for wall or ceiling

• • Dimensions/weight (AP-584 unit only):
    • 324mm (W) x 312mm (D) x 244mm (H) / 12.6” (W) x 12.3” (D) x 9.6” (H)
    • 5.52 kg / 11.5 lbs
  • Dimensions/weight (AP-584 shipping pkg, no mount):
    • 410mm (W) x 322mm (D) x 433mm (H) / 16.1” (W) x 12.7” (D) x 17” (H)
    • 7.56 kg / 16.8 lbs

AP-585

• • Dimensions/weight (AP-585 unit only):
    • 324mm (W) x 313mm (D) x 320mm (H) / 12.6” (W) x 12.3” (D) x 12.7” (H)
    • 5.24 kg / 11.5 lbs
  • Dimensions/weight (AP-585 shipping pkg, no mount):
    • 431mm (W) x 415mm (D) x 442mm (H) / 17” (W) x 16.3” (D) x 17.4” (H)
    • 7.81 kg / 17.2 lbs
• AP-587
  • Dimensions/weight (AP-587 unit only):
    • 302mm (W) x 300mm (D) x 174mm (H) / 11.9” (W) x 11.8” (D) x 6.9” (H)
    • 4.51 kg / 9.9 lbs
  • Dimensions/weight (AP-587 shipping pkg, no mount):
    • 385mm (W) x 272mm (D) x 433mm (H) / 15.2” (W) x 10.7” (D) x 17” (H)
    • 6.03 kg / 13.3 lbs

• • Temperature: -40°C to +65°C / -40°F to +149°F with full solar loading
  • Humidity: 5% to 93% non-condensing internal
  • Rated for operation in all weather conditions

Storage and transportation conditions

• • Temperature: -40°C to +70°C / -40°F to +158°F

Operating Altitude: 3,000 m

Water and Dust: IP66/67

Salt Tolerance: Test to ASTM B117-07A Salt Spray 200hrs

Wind Survival: 150mph (GR-487)

CE Marked

RED Directive 2014/53/EU

EMC Directive 2014/30/EU

Low Voltage Directive 2014/35/EU

UL/IEC/EN 60950-1

UL/IEC/EN 62368-1

IEC 60950-22

IEC/EN60601-1-2

EN 50155

For more country-specific regulatory information and approvals, please see your Aruba representative.

AP-585: APEX0585

AP-587: APEX0587

Bluetooth SIG

Ethernet Alliance (E0, PoE PD device, class 6; E2, PoE PSE device, class 3)

ArubaOS 10.4.0.0