670-series

Wi-Fi 6E for extreme outdoor conditions

Provide secure and reliable connectivity in large outdoor open areas, such as stadiums and public venues with weatherproof high-performance Wi-Fi 6E APs.

Wi-Fi 6E performance

Improve Wi-Fi performance using the 6 GHz band for faster speeds and wider channels. Tri-band coverage across 2.4 GHz, 5 GHz, and 6 GHz delivers 3.9 Gbps maximum aggregate data rate supports high-bandwidth, low-latency applications such as high-definition video.

Ruggedized for outdoors

Withstand extreme high and low temperatures, persistent moisture, and precipitation. Fully sealed to keep out airborne contaminants and electrical interfaces including industrial-strength surge protection. Available with choice of internal antenna (omni, directional, or point-to-point) to optimize wireless coverage.

IoT ready

Deploy and manage enterprise and industrial IoT, including asset tracking services, security solutions, and sensors, with integrated high-power Bluetooth and 802.15.4 radios for Zigbee support. Advanced IoT Coexistence (AIC) helps Wi-Fi, Bluetooth and Zigbee radios operate at maximum capacity without interference.

Location aware

Protect incumbent outdoor services via self-locating embedded GPS receivers that operate as Standard Power (SP) devices, requiring an Automated Frequency Coordination service (AFC).

Efficient and secure

Extend the 802.11ax standard to the 6GHz band, including efficiency and security enhancements such as orthogonal frequency-division multiple access (OFDMA), multi-user MIMO, enhanced open, and WPA3 with Wi-Fi 6E. The 670 Series APs also offers client optimization, automated radio frequency management, and intelligent power monitoring.

Additional information

Number of radios	1, 2
Performance Density	Very High

Specifications

Hardware variants
HPE Aruba Networking AP-675 Built in omnidirectional antennas 2.4 GHz antennas 3.5dBi 5 GHz antennas 5dBi 6 GHz antennas 5dBi BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 6dBi HPE Aruba Networking AP-677 Built in directional antennas 2.4 GHz antennas 5.6dBi 5 GHz antennas 6dBi 6 GHz antennas 7dBi BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 8dBi HPE Aruba Networking AP-679 Built in dynamic directional antennas 2.4 GHz antennas 6dBi 5 GHz antennas Wide 9dBi Narrow 12dBi 6 GHz antennas Wide 9dBi Narrow 13dBi BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 6dBi

Hardware variants

HPE Aruba Networking AP-675

- Built in omnidirectional antennas
- 2.4 GHz antennas 3.5dBi
- 5 GHz antennas 5dBi
- 6 GHz antennas 5dBi
- BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 6dBi

HPE Aruba Networking AP-677

- Built in directional antennas
- 2.4 GHz antennas 5.6dBi
- 5 GHz antennas 6dBi
- 6 GHz antennas 7dBi
- BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 8dBi

HPE Aruba Networking AP-679

- Built in dynamic directional antennas
- 2.4 GHz antennas 6dBi
- 5 GHz antennas
  - Wide 9dBi
  - Narrow 12dBi
- 6 GHz antennas
  - Wide 9dBi
  - Narrow 13dBi
- BLE/Zigbee: Integrated omnidirectional antenna with peak gain of 6dBi

Wi-Fi radio specifications
AP type: Outdoor, tri radio, 2.4GHz, 5GHz and 6GHz (concurrent) 802.11ax 2×2 MIMO 2.4 GHz radio: Two spatial stream single user (SU) MIMO for up to 574 Mbps wireless data rate with 2SS HE40 802.11ax client devices 5 GHz radio: Two spatial stream single user (SU) MIMO for up to 1.2 Gbps wireless data rate with 2SS HE80 802.11ax client devices 6 GHz radio: Two spatial stream single user (SU) MIMO for up to 2.4 Gbps wireless data rate with 2SS HE160 802.11ax client devices Up to 512 associated client devices per radio, and up to 16 BSSIDs per radio (limited to 8 for the 6GHz radio) Supported frequency bands (country-specific restrictions apply): 2.400 to 2.4835 GHz ISM 5.150 to 5.250 GHz U-NII-1 5.250 to 5.350 GHz U-NII-2 5.470 to 5.725 GHz U-NII-2E 5.725 to 5.850 GHz U-NII-3/ISM 5.850 to 5.895 GHz U-NII-4 5.925 to 6.425 GHz U-NII-5 6.425 to 6.525 GHz U-NII-6 6.525 to 6.875 GHz U-NII-7 6.875 to 7.125 GHz U-NII-8 Available bands and channels: Dependent on configured regulatory domain (country) Dynamic frequency selection (DFS) optimizes the use of available RF spectrum in the 5 GHz band Supported radio technologies: 802.11b: Direct-sequence spread-spectrum (DSSS) 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 8 resource units (37 for the 6GHz radio) Supported Modulation Types 802.11b: BPSK, QPSK, CCK 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM and 256-QAM (proprietary extension) 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM (proprietary extension) 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, and 1024-QAM 802.11n high-throughput (HT) support: HT20/40 802.11ac very high throughput (VHT) support: VHT20/40/80 802.11ax high efficiency (HE) support: HE20/40/80/160 Supported data rates (Mbps): 802.11b: 1, 2, 5.5, 11 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 802.11n: 6.5 to 300 (MCS0 to MCS15, HT20 to HT40), 400 with 256-QAM (proprietary extension) 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2, VHT20 to VHT80); 1,083 with 1024-QAM (MCS10 and MCS11, proprietary extension) 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40) 802.11ax (5GHz): 3.6 to 1,201 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE80) 802.11ax (6GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE160) 802.11n/ac packet aggregation: A-MPDU, A-MSDU Transmit power: Configurable in increments of 0.5 dBm Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements) Per radio/band (2.4 GHz/5 GHz/6 GHz): +25 dBm (18 dBm per chain) Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain. Advanced cellular coexistence (ACC) minimizes the impact of interference from cellular networks Maximum ratio combining (MRC) for improved receiver performance Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance Space-time block coding (STBC) for increased range and improved reception Low-density parity check (LDPC) for high- efficiency error correction and increased throughput Transmit beamforming (TxBF) for increased signal reliability and range 802.11ax Target Wait Time (TWT) to support low-power client devices 802.11mc Fine Timing Measurement (FTM) for precision distance ranging

Wi-Fi radio specifications

AP type: Outdoor, tri radio, 2.4GHz, 5GHz and 6GHz (concurrent) 802.11ax 2×2 MIMO

2.4 GHz radio: Two spatial stream single user (SU) MIMO for up to 574 Mbps wireless data rate with 2SS HE40 802.11ax client devices

5 GHz radio: Two spatial stream single user (SU) MIMO for up to 1.2 Gbps wireless data rate with 2SS HE80 802.11ax client devices

6 GHz radio: Two spatial stream single user (SU) MIMO for up to 2.4 Gbps wireless data rate with 2SS HE160 802.11ax client devices

Up to 512 associated client devices per radio, and up to 16 BSSIDs per radio (limited to 8 for the 6GHz radio)

Supported frequency bands (country-specific restrictions apply):

- 2.400 to 2.4835 GHz ISM
- 5.150 to 5.250 GHz U-NII-1
- 5.250 to 5.350 GHz U-NII-2
- 5.470 to 5.725 GHz U-NII-2E
- 5.725 to 5.850 GHz U-NII-3/ISM
- 5.850 to 5.895 GHz U-NII-4
- 5.925 to 6.425 GHz U-NII-5
- 6.425 to 6.525 GHz U-NII-6
- 6.525 to 6.875 GHz U-NII-7
- 6.875 to 7.125 GHz U-NII-8

Available bands and channels: Dependent on configured regulatory domain (country)

Dynamic frequency selection (DFS) optimizes the use of available RF spectrum in the 5 GHz band

Supported radio technologies:

802.11b: Direct-sequence spread-spectrum (DSSS)

802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)

802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 8 resource units (37 for the 6GHz radio)

Supported Modulation Types

- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM and 256-QAM (proprietary extension)
- 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM (proprietary extension)
- 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, and 1024-QAM

802.11n high-throughput (HT) support: HT20/40

802.11ac very high throughput (VHT) support: VHT20/40/80

802.11ax high efficiency (HE) support: HE20/40/80/160

Supported data rates (Mbps):

- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 300 (MCS0 to MCS15, HT20 to HT40), 400 with 256-QAM (proprietary extension)
- 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2, VHT20 to VHT80); 1,083 with 1024-QAM (MCS10 and MCS11, proprietary extension)
- 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40)
- 802.11ax (5GHz): 3.6 to 1,201 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE80)
- 802.11ax (6GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE160)

802.11n/ac packet aggregation: A-MPDU, A-MSDU

Transmit power: Configurable in increments of 0.5 dBm

Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements)

- Per radio/band (2.4 GHz/5 GHz/6 GHz): +25 dBm (18 dBm per chain)
- Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain.

Advanced cellular coexistence (ACC) minimizes the impact of interference from cellular networks

Maximum ratio combining (MRC) for improved receiver performance

Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance

Space-time block coding (STBC) for increased range and improved reception

Low-density parity check (LDPC) for high- efficiency error correction and increased throughput

Transmit beamforming (TxBF) for increased signal reliability and range

802.11ax Target Wait Time (TWT) to support low-power client devices

802.11mc Fine Timing Measurement (FTM) for precision distance ranging

Power
The AP supports power over ethernet (PoE) on port E0 Power sources are sold separately; see the HPE Aruba Networking 67 Series ordering guide for details When powered by 802.3bt (class 6) PoE, the AP will operate without restrictions. When powered by 802.3bt (class 5) PoE with the IPM feature disabled, the AP will disable the USB-C port. Operating the AP with an 802.3at (class 4) POE with the IPM feature disabled, the AP will disable the USB ports, the SFP port, and one of the two chains on the 2.4Ghz radio Operating the AP with an 802.3af (class 3 or lower) POE source is not supported (except for AP staging) With IPM enabled, the AP will start up in unrestricted mode but may dynamically apply restrictions depending on the available power budget and actual consumption. The feature restrictions and order in which these get applied are configurable. Maximum (worst-case) power consumption (without/with a USB device attached): PoE powered: 29W/45.5W. This assumes that up to 16.5W total is supplied the attached USB devices Maximum (worst-case) power consumption in idle mode: 11W/27.5W (both USB active at max). Maximum (worst-case) power consumption in deep-sleep mode: 3.2W (PoE).

Power

The AP supports power over ethernet (PoE) on port E0

Power sources are sold separately; see the HPE Aruba Networking 67 Series ordering guide for details

When powered by 802.3bt (class 6) PoE, the AP will operate without restrictions.

When powered by 802.3bt (class 5) PoE with the IPM feature disabled, the AP will disable the USB-C port.

Operating the AP with an 802.3at (class 4) POE with the IPM feature disabled, the AP will disable the USB ports, the SFP port, and one of the two chains on the 2.4Ghz radio

Operating the AP with an 802.3af (class 3 or lower) POE source is not supported (except for AP staging)

With IPM enabled, the AP will start up in unrestricted mode but may dynamically apply restrictions depending on the available power budget and actual consumption. The feature restrictions and order in which these get applied are configurable.

Maximum (worst-case) power consumption (without/with a USB device attached):

- PoE powered: 29W/45.5W.
- This assumes that up to 16.5W total is supplied the attached USB devices

Maximum (worst-case) power consumption in idle mode: 11W/27.5W (both USB active at max).

Maximum (worst-case) power consumption in deep-sleep mode: 3.2W (PoE).

Additional Interfaces
Wired network interface (E0) Auto-sensing link speed (100/1000/2500BASE-T) and MDI/MDX 2.5 Gbps speed complies with NBase-T and 802.3bz specifications PoE-PD: 48Vdc (nominal) 802.3at/bt PoE (class 4 or higher) 802.3az Energy Efficient Ethernet (EEE) Wired network interface (E1) SFP Fiber Port When used in operation it is expected that this is the primary uplink port -Only recommended industrial temperature SFP/SFP+ modules should be used for optimal performance USB 3.0 host interface (type C connector), supporting 2A/10W maximum USB 2.0 host interface (type A connector), supporting 1A/5W maximum Bluetooth low energy (BLE5.0) and Zigbee (802.15.4) radio BLE: up to 8 dBm transmit power (class 1) and -100 dBm receive sensitivity (125 kbps) Zigbee: up to 8 dBm transmit power and -97 dBm receive sensitivity (250 kbps) GNSS L1 (1575.42 MHz) receiver supporting GPS, Galileo, GLONASS, and BeiDou signal Receive sensitivity: -163 dBm (tracking) Integrated antenna with gain of ~2 dBi Advanced IoT coexistence (AIC) allows concurrent operation of multiple radios in the 2.4 GHz band Built-in trusted platform module (TPM) for enhanced security and anti-counterfeiting Visual indicators for system and radio status (1x multi-color LED), auto-disable after 15min when up Reset button: factory reset, LED mode control (normal/off) Serial console interface (proprietary, USB-C physical jack) Automatic thermal shutdown and recovery function

Additional Interfaces

Wired network interface (E0)

- Auto-sensing link speed (100/1000/2500BASE-T) and MDI/MDX
- 2.5 Gbps speed complies with NBase-T and 802.3bz specifications
- PoE-PD: 48Vdc (nominal) 802.3at/bt PoE (class 4 or higher)
- 802.3az Energy Efficient Ethernet (EEE)

Wired network interface (E1)

- SFP Fiber Port
- When used in operation it is expected that this is the primary uplink port
- -Only recommended industrial temperature SFP/SFP+ modules should be used for optimal performance

USB 3.0 host interface (type C connector), supporting 2A/10W maximum

USB 2.0 host interface (type A connector), supporting 1A/5W maximum

Bluetooth low energy (BLE5.0) and Zigbee (802.15.4) radio

BLE: up to 8 dBm transmit power (class 1) and -100 dBm receive sensitivity (125 kbps)

Zigbee: up to 8 dBm transmit power and -97 dBm receive sensitivity (250 kbps)

GNSS L1 (1575.42 MHz) receiver supporting GPS, Galileo, GLONASS, and BeiDou signal

Receive sensitivity: -163 dBm (tracking)

Integrated antenna with gain of ~2 dBi

Advanced IoT coexistence (AIC) allows concurrent operation of multiple radios in the 2.4 GHz band

Built-in trusted platform module (TPM) for enhanced security and anti-counterfeiting

Visual indicators for system and radio status (1x multi-color LED), auto-disable after 15min when up

Reset button: factory reset, LED mode control (normal/off)

Serial console interface (proprietary, USB-C physical jack)

Automatic thermal shutdown and recovery function

Mounting
A mounting bracket holder has been pre-installed on the top of the AP. This bracket is used to secure the AP to any of the mount kits (sold separately); see the HPE Aruba Networking 670 Series Ordering Guide for details. The HPE Aruba Networking 670 Series Outdoor access points also share the same mounting hardware and accessories so upgrades from previous HPE Aruba Networking outdoor access points are quick and easy. AP-OUT-MNT-V1A: Outdoor Pole/Wall Long Mount Kit AP-270-MNT-V2: Outdoor Pole/Wall Short Mount Kit AP-270-MNT-H1: Outdoor AP Hanging or Tilt Install Mount Kit AP-270-MNT-H2: Outdoor Flush Wall or Ceiling Mount AP-270-MNT-H3: Outdoor AP Hanging or Dual-Tilt Install Mount Kit

Mounting

A mounting bracket holder has been pre-installed on the top of the AP. This bracket is used to secure the AP to any of the mount kits (sold separately); see the HPE Aruba Networking 670 Series Ordering Guide for details. The HPE Aruba Networking 670 Series Outdoor access points also share the same mounting hardware and accessories so upgrades from previous HPE Aruba Networking outdoor access points are quick and easy.

- AP-OUT-MNT-V1A: Outdoor Pole/Wall Long Mount Kit
- AP-270-MNT-V2: Outdoor Pole/Wall Short Mount Kit
- AP-270-MNT-H1: Outdoor AP Hanging or Tilt Install Mount Kit
- AP-270-MNT-H2: Outdoor Flush Wall or Ceiling Mount
- AP-270-MNT-H3: Outdoor AP Hanging or Dual-Tilt Install Mount Kit

Mechanical
AP-675 Dimensions/weight (unit only): 290mm (W) x 288mm (D) x 312mm (H) 11.4 in (W) x 11.3 in (D) x 12.3in (H) 4kg / 8.8lbs AP-677 Dimensions/weight (unit only): 290 (W) x 288mm (D) x 171mm (H) 11.4 in (W) x 11.3 in (D) x 6.7 in (H) 3.6kg / 7.9lbs AP-679 Dimensions/weight (unit only): 290mm (W) x 288mm (D) x 171mm (H) 11.4 in (W) x 11.3 in (D) x 6.7 in (H) 3.8kg / 8.4lbs

Mechanical

AP-675

- Dimensions/weight (unit only):
  - 290mm (W) x 288mm (D) x 312mm (H)
  - 11.4 in (W) x 11.3 in (D) x 12.3in (H)
  - 4kg / 8.8lbs

AP-677

- Dimensions/weight (unit only):
  - 290 (W) x 288mm (D) x 171mm (H)
  - 11.4 in (W) x 11.3 in (D) x 6.7 in (H)
  - 3.6kg / 7.9lbs

AP-679

- Dimensions/weight (unit only):
  - 290mm (W) x 288mm (D) x 171mm (H)
  - 11.4 in (W) x 11.3 in (D) x 6.7 in (H)
  - 3.8kg / 8.4lbs

Environmental
Operating conditions Temperature: -40 °C to +70 °C / -40 °F to 158 °F (no solar loading), -40 °C to +65 °C / -40 °F to 149 °F (with solar loading) Humidity: 5% to 100% non-condensing internal Rated for operation in all weather conditions Storage and transportation conditions Temperature: -40C to +70C / -40F to +158F Operating Altitude: 3000m Water and Dust IP66/67 Salt Tolerance Test to ASTM B117-07A Salt Spray 200hrs Wind Survival: 150mph (GR-487)

Environmental

Operating conditions

- Temperature: -40 °C to +70 °C / -40 °F to 158 °F (no solar loading), -40 °C to +65 °C / -40 °F to 149 °F (with solar loading)
- Humidity: 5% to 100% non-condensing internal
- Rated for operation in all weather conditions

Storage and transportation conditions

- Temperature: -40C to +70C / -40F to +158F

Operating Altitude: 3000m

Water and Dust

- IP66/67

Salt Tolerance

- Test to ASTM B117-07A Salt Spray 200hrs

Wind Survival: 150mph (GR-487)

Reliability
Mean time between failure (MTBF): 500,562hrs (59.4 yrs.) at +25C ambient operating temperature.

Regulatory compliance
FCC/ISED CE marked RED directive 2014/53/EU IEC/EN 62368-1 EN 60601-1-1, EN60601-1-2 For more country-specific regulatory information and approvals, please see your HPE Aruba Networking representative.

Regulatory compliance

FCC/ISED

CE marked

RED directive 2014/53/EU

IEC/EN 62368-1

EN 60601-1-1, EN60601-1-2

For more country-specific regulatory information and approvals, please see your HPE Aruba Networking representative.

Regulatory model numbers
AP-675: APEX0675 AP-677: APEX0677 AP-679: APEX0679

Regulatory model numbers

AP-675: APEX0675

AP-677: APEX0677

AP-679: APEX0679

Certifications
Wi-Fi Alliance: Bluetooth SIG Ethernet Alliance (E0, PoE PD device, class 6)

Certifications

Wi-Fi Alliance:

Bluetooth SIG

Ethernet Alliance (E0, PoE PD device, class 6)

Minimum Operating System Software Versions
HPE Aruba Networking Wireless Operating System AOS-10.7.0.0 HPE Aruba Networking Wireless Operating System AOS-8.12.0.0 HPE Aruba Networking Instant Operating System AOS-8.12.0.0 (no 6GHz support with Instant)

Warranty
HPE Aruba Networking hardware limited lifetime warranty

Wi-Fi 6E for the extreme outdoors

6 GHz support

Standard power (SP) device operations

IP66/67 rated for challenging conditions

Multi-gigabit ethernet speeds

High-power Bluetooth and Zigbee radios

Built-in security

Wi-Fi 6E for extreme outdoor conditions

Wi-Fi 6E performance

Ruggedized for outdoors

IoT ready

Location aware

Efficient and secure

Additional information

Specifications

Resources

Data Sheet

Manuals and Guides

Main Menu

670-series

Wi-Fi 6E for the extreme outdoors

6 GHz support

Standard power (SP) device operations

IP66/67 rated for challenging conditions

Multi-gigabit ethernet speeds

High-power Bluetooth and Zigbee radios

Built-in security

Wi-Fi 6E for extreme outdoor conditions

Wi-Fi 6E performance

Ruggedized for outdoors

IoT ready

Location aware

Efficient and secure

Additional information

Specifications

Resources

Data Sheet

Manuals and Guides

Related products

370 Series

580-series

518-series

318-series

560ex-series

Main Menu